#4

...ask your questions in the appropriate forums BUT document your build here...preferably in a single thread...dates for updates, are appreciated....

Re: #4

Postby bdosborn » Wed Oct 02, 2019 7:14 pm

Thanks, I found it on Amazon and saved it to my trailer wish list. I jackknifed the truck too far and punched a hole in mine. :x

Tongue Box

Bruce
2009 6.5'X11' TTT - Boxcar
Image
Boxcar Build
User avatar
bdosborn
Donating Member
 
Posts: 4457
Images: 477
Joined: Wed May 05, 2004 11:10 pm
Location: CO, Littleton

Re: #4

Postby tony.latham » Wed Oct 02, 2019 7:16 pm

bdosborn wrote:Thanks, I found it on Amazon and saved it to my trailer wish list. I jackknifed the truck too far and punched a hole in mine. :x

Tongue Box

Bruce


:thumbsup:
User avatar
tony.latham
Gold Donating Member
 
Posts: 3749
Images: 17
Joined: Mon Jul 08, 2013 4:03 pm
Location: Middle of Idaho on the edge of nowhere

Re: #4

Postby campbellinaz » Wed Oct 09, 2019 11:55 pm

KTM_Guy wrote:
campbellinaz wrote:
KTM_Guy wrote:
campbellinaz wrote:Enjoying following your build Tony! I’m currently in the midst of a build and pricing out sheet aluminum in the Phoenix area is crazy expensive! I’m in need of 5x10 sheets which I’m told are only available in .063 and I’m seeing prices just shy of $300/sheet . So I’m looking at “liners” now as they are much less expensive. Although glass/epoxy is far more time consuming it can’t be as expensive as 3-4 sheets at $300 a copy.


Sent from my iPhone using Tapatalk


Don’t go to IMS in PHX, I found a place and got .040 5X10 I think was $60 a sheet. Can’t remember the name right now. It was west of downtown.

Todd


Todd, I’m really interested if your able to figure out where you got the aluminum. I’m afraid the tariff saga has changed buying aluminum forever.


Sent from my iPhone using Tapatalk


I bought from

Coast Aluminum and Architectural
4455 W MAgnolia St
Phoenix, AZ 85043
602-278-5052

They mostly deal with truck load orders but didn't seem to mind my small order.

Another place to check is Davis Scrap just north of Sky Harbor. Some times they will have thin gauge aluminum sheets but mostly 16 gauge and up. Still a fun place to check out. The other week I was looking around in the yard and there was about 10 pieces of 20X20X12 blocks of aluminum. :?

Todd


Thanks for the info Todd!


Sent from my iPhone using Tapatalk
campbellinaz
Teardrop Inspector
 
Posts: 15
Joined: Wed Mar 21, 2018 2:20 am
Top

Re: #4

Postby ricky herbold » Fri Oct 11, 2019 2:43 pm

Can you please explain how you did that with tissue paper

tony.latham wrote:Image

The devil is in the details. :frightened:

Tony

p.s. that's done with tissue paper
ricky herbold
Teardrop Builder
 
Posts: 41
Images: 0
Joined: Sat Jul 27, 2019 6:14 am
Location: Spring Valley Lake CA.
Top

Re: #4

Postby tony.latham » Fri Oct 11, 2019 4:04 pm

Can you please explain how you did that with tissue paper


Get your final design printed on regular paper and then tape the tissue paper over it. I use just enough tissue to cover the print plus room for tape. Stick it back in the printer and push the button.

Wet the spot out with the same varnish you used on the wood, set it in place making sure it's level and then saturate the tissue paper.

Image

The challenge is finding the right tissue paper. The first stuff I tired wrinkled when wetted out. I can't give you a brand since I found this stuff in with our gift-wrap papers. I suggest you finish a piece of scrap plywood with your varnish and then test your printed tissue paper on it.

:thumbsup:

Tony
User avatar
tony.latham
Gold Donating Member
 
Posts: 3749
Images: 17
Joined: Mon Jul 08, 2013 4:03 pm
Location: Middle of Idaho on the edge of nowhere
Top

Re: #4

Postby ricky herbold » Fri Oct 11, 2019 4:34 pm

tony.latham wrote:
Can you please explain how you did that with tissue paper


Get your final design printed on regular paper and then tape the tissue paper over it. I use just enough tissue to cover the print plus room for tape. Stick it back in the printer and push the button.

Wet the spot out with the same varnish you used on the wood, set it in place making sure it's level and then saturate the tissue paper.

Image

The challenge is finding the right tissue paper. The first stuff I tired wrinkled when wetted out. I can't give you a brand since I found this stuff in with our gift-wrap papers. I suggest you finish a piece of scrap plywood with your varnish and then test your printed tissue paper on it.

:thumbsup:

Tony

That is awesome. I have some experimenting to do. Thanks!!
ricky herbold
Teardrop Builder
 
Posts: 41
Images: 0
Joined: Sat Jul 27, 2019 6:14 am
Location: Spring Valley Lake CA.
Top

Re: #4

Postby tony.latham » Fri Oct 11, 2019 5:32 pm

I got the personalized plate on her.

Image

:shock:

Tony
User avatar
tony.latham
Gold Donating Member
 
Posts: 3749
Images: 17
Joined: Mon Jul 08, 2013 4:03 pm
Location: Middle of Idaho on the edge of nowhere
Top

Re: #4

Postby bdosborn » Fri Oct 11, 2019 6:29 pm

That is cool!
Bruce
2009 6.5'X11' TTT - Boxcar
Image
Boxcar Build
User avatar
bdosborn
Donating Member
 
Posts: 4457
Images: 477
Joined: Wed May 05, 2004 11:10 pm
Location: CO, Littleton
Top

Previous

Return to Build Journals

Who is online

Users browsing this forum: No registered users and 6 guests