275 Franken-Lantern instructions. Picture heavy

Lanterns, stoves, etc... anything old!

275 Franken-Lantern instructions. Picture heavy

Postby Mukilteo » Sun Sep 29, 2013 9:38 am

Here is how I did it using a 275 fount and a 200A valve stem on up assembly.
One should use Safety glasses and face masks.
First find you first victim. A Coleman 275 that hasn't been used in years.
Image
Tear her down. I even pull the check valve.
Image
Image
I will flush out the fount with water to get any residual fuel out and heat with a mini torch the area where the valve stem treads into the fount to break loose the sealer Coleman uses.
Than I lock the valve stem in the vice. Not too tight.
Image
Put a rubber drawer liner on her to get a better grip and spin her off.
Image
Image
This is where you want to cut the valve stem off.
Image
I use my Dremel cutting disc.
Image
The added length gives you room to grip it with Vice Grips to re-thread it back into the 275 fount.
Image
Stripped the paint.
Image
Got her ready for painting.
Image
Put a little sealer on the valve stem threads.
Image
I made the mistake of painting before threading in the cut down 275 valve stem.
Image
Than cut if flush with the fount with my Dremel cutting disk.
Image
The inner opening doesn't need the hole re drilled as it is very close to the size for the tap.
Image
The next picture come from Saltfork at the Coleman Collector Forum because I forgot to document this part.
The 200A fount is 1/2 inch taller than the 275 fount so you will need to trim the 200A FA tube.
Image
To be continued. Need a coffee break.
Edited for accuracy.
Last edited by Mukilteo on Sun Sep 29, 2013 11:31 am, edited 2 times in total.
Eric
Mukilteo
Donating Member
 
Posts: 1355
Images: 18
Joined: Sun Apr 01, 2007 8:14 am

Re: 275 Franken-Lantern instructions. Picture heavy

Postby Mukilteo » Sun Sep 29, 2013 10:03 am

The next three pictures come from Saltfork at the Coleman Collector Forum because I forgot to document this part.
Next disassemble the FA tube and desolder the tip
Image
With the fuel rod removed cut 1/2 inch off the end of the FA tube. It's a tube with in a tube. cut thru both.
Image
This is the reassembled and resoldered tube before cutting the fuel rod to length.
You will have to have the valve assembled to trim the rod to the right length to make sure it retracts enough to allow fuel flow when the valve is opened.
Image
Reassembled doing a pressure check.
Image
Done.
Image
and the $$$ shot.
Image
Thanks for looking.
Eric
Mukilteo
Donating Member
 
Posts: 1355
Images: 18
Joined: Sun Apr 01, 2007 8:14 am

Re: 275 Franken-Lantern instructions. Picture heavy

Postby High Desert » Sun Sep 29, 2013 10:28 am

Excellent tutorial Eric, you do some fine work. The black band finish is a great touch. :thumbsup:
Shaun

"it's not the years honey, it's the mileage"
High Desert
Platinum Donating Member
 
Posts: 8780
Images: 27
Joined: Wed Apr 08, 2009 1:46 pm
Location: SW Washington state
Top

Re: 275 Franken-Lantern instructions. Picture heavy

Postby campmaster-k » Sun Sep 29, 2013 11:25 am

Thanks Eric. You just answered all of my questions.
-Kirk

>TnTTT ORIGINAL 200A LANTERN CLUB

>CEO Coleman Recovery Inc.

>Nor Cal Camping Pinewood Racing Team


Build thread -

viewtopic.php?t=45307&postdays=0&postorder=asc&start=180

Check out my Pictures -

http://s1199.photobucket.com/albums/aa4 ... 0QQtppZZ24
User avatar
campmaster-k
Lifetime member
 
Posts: 3030
Images: 17
Joined: Fri Jun 17, 2011 5:02 pm
Location: Colusa, California
Top

Re: 275 Franken-Lantern instructions. Picture heavy

Postby Mukilteo » Sun Sep 29, 2013 11:34 am

Just paint after putting the bushing. That way you don't have to worry about scratching your new paint job tightening the bushing down.
I forgot that with this one.
Eric
Mukilteo
Donating Member
 
Posts: 1355
Images: 18
Joined: Sun Apr 01, 2007 8:14 am
Top

Re: 275 Franken-Lantern instructions. Picture heavy

Postby Kevin A » Sun Sep 29, 2013 12:48 pm

Great tutorial. :applause: One of the steps has me thinking though. If the bushing was left a 1/2" taller the F/A tube wouldn't need to be shortened. This would also locate the valve wheel and tip cleaner lever that much higher above the larger diameter fount. The only drawback would be the need to fabricate a taller frame rest/collar. I suppose one could also machine flats on the bushing to allow the use of a wrench to tighten it. :thinking:
"Follow me, I'm right behind you"

ImageImage
User avatar
Kevin A
The other guy
 
Posts: 3222
Images: 289
Joined: Mon Jan 17, 2005 1:16 am
Location: California, Eureka
Top

Re: 275 Franken-Lantern instructions. Picture heavy

Postby Mukilteo » Sun Sep 29, 2013 1:39 pm

For me, shortening the FA tube is easier than trying to make a new collar.
It's the KISS technique.
Eric
Mukilteo
Donating Member
 
Posts: 1355
Images: 18
Joined: Sun Apr 01, 2007 8:14 am
Top

Re: 275 Franken-Lantern instructions. Picture heavy

Postby Mukilteo » Sun Sep 29, 2013 11:13 pm

My collection of Fat Bottom Girls.
Image
Eric
Mukilteo
Donating Member
 
Posts: 1355
Images: 18
Joined: Sun Apr 01, 2007 8:14 am
Top

Re: 275 Franken-Lantern instructions. Picture heavy

Postby campmaster-k » Mon Sep 30, 2013 9:18 am

Mukilteo wrote:My collection of Fat Bottom Girls.
Image


"Fat Bottom Girls" - Now thats a gang name! :lol:
-Kirk

>TnTTT ORIGINAL 200A LANTERN CLUB

>CEO Coleman Recovery Inc.

>Nor Cal Camping Pinewood Racing Team


Build thread -

viewtopic.php?t=45307&postdays=0&postorder=asc&start=180

Check out my Pictures -

http://s1199.photobucket.com/albums/aa4 ... 0QQtppZZ24
User avatar
campmaster-k
Lifetime member
 
Posts: 3030
Images: 17
Joined: Fri Jun 17, 2011 5:02 pm
Location: Colusa, California
Top

Re: 275 Franken-Lantern instructions. Picture heavy

Postby wagondude » Tue Oct 01, 2013 8:34 am

campmaster-k wrote:
Mukilteo wrote:My collection of Fat Bottom Girls.
Image


"Fat Bottom Girls" - Now thats a gang name! :lol:


And "they make this rockin' world go 'round". :D
Bill

TnTTT ORIGIONAL 200A LANTERN CLUB
101137
User avatar
wagondude
1000 Club
1000 Club
 
Posts: 1535
Images: 35
Joined: Sun Jan 16, 2011 7:41 pm
Location: Land of the Jayhawks
Top


Return to Vintage Camping Equipment

Who is online

Users browsing this forum: No registered users and 2 guests