4x8 ----> 5x10 ?

Ask questions about Harbor Freight trailers, or questions about building your own...

4x8 ----> 5x10 ?

Postby tianac2 » Fri Jul 10, 2009 6:53 pm

I realize that this is probably a somewhat ridiculous question, but can a 5x10 teardrop be built on a 4x8 frame? Why?
tianac2
Teardrop Inspector
 
Posts: 12
Joined: Wed Jul 08, 2009 10:19 pm

Re: 4x8 ----> 5x10 ?

Postby Steve_Cox » Fri Jul 10, 2009 10:57 pm

tianac2 wrote:I realize that this is probably a somewhat ridiculous question, but can a 5x10 teardrop be built on a 4x8 frame? Why?



1. yes
2. why not?
Steve
User avatar
Steve_Cox
4000 Club
4000 Club
 
Posts: 4903
Images: 196
Joined: Sun Apr 03, 2005 8:46 am
Location: Albuquerque New Mexico

Re: 4x8 ----> 5x10 ?

Postby tianac2 » Fri Jul 10, 2009 11:03 pm

Steve_Cox wrote:
tianac2 wrote:I realize that this is probably a somewhat ridiculous question, but can a 5x10 teardrop be built on a 4x8 frame? Why?



1. yes
2. why not?


:lol:

Fair enough. Alright, then, HOW would one go about doing that? Raise the frame? Build the deck out over the wheels? Is it possible to do it without building over the wheels?
tianac2
Teardrop Inspector
 
Posts: 12
Joined: Wed Jul 08, 2009 10:19 pm
Top

Postby 2bits » Sat Jul 11, 2009 11:43 am

Replace the axle with a wider one if you don't want to build out over it, otherwise you would need to build over the axle. as far the the floor goes, just build the floor bigger than the trailer and let it over hang a tad , no biggie!
Thomas

Image
User avatar
2bits
2bit Member
 
Posts: 5130
Images: 8
Joined: Thu Dec 27, 2007 6:04 pm
Location: Lake Tawakoni, TX
Top

Postby tianac2 » Sat Jul 11, 2009 2:38 pm

2bits wrote:Replace the axle with a wider one if you don't want to build out over it, otherwise you would need to build over the axle. as far the the floor goes, just build the floor bigger than the trailer and let it over hang a tad , no biggie!


Awesome! That's exactly what I needed to know....Thanks!
tianac2
Teardrop Inspector
 
Posts: 12
Joined: Wed Jul 08, 2009 10:19 pm
Top

Re: 4x8 ----> 5x10 ?

Postby mikeschn » Sat Jul 11, 2009 7:53 pm

tianac2 wrote:I realize that this is probably a somewhat ridiculous question, but can a 5x10 teardrop be built on a 4x8 frame? Why?


It's easy enough to build out over the wheels. If you use a harbor freight chassis, your teardrop will probably be closer to 66" wide. See my Escape Hatch to see how I did it... http://www.mikenchell.com/WWEH_Photo_Album/

Stretching it to 10' is a little bit tougher. It really helps if you can start with a 4x10 trailer chassis.

One of the things you have to be concerned about is that you don't build a larger floor on a smaller chassis, and end up with the trampoline effect.

Mike...
The quality is remembered long after the price is forgotten, so build your teardrop with the best materials...
User avatar
mikeschn
Site Admin
 
Posts: 19202
Images: 479
Joined: Tue Apr 13, 2004 11:01 am
Location: MI
Top

Postby Tommy2tone_1999 » Tue Dec 29, 2009 10:37 pm

Hey Mike,

Kaspersky Internet Security flagged the web address you gave as:

The requested object is INFECTED with the following viruses: HEUR:Trojan.Script.Iframer



Hope this helps.

Tommy
Make time for fitness and it'll make time for you.
http://TommyDoran.com
http://tommydoran.com/favor
Interview: http://goo.gl/Non1oR
Build Journal - http://www.tnttt.com/viewtopic.php?f=50&t=58395
Come find me on Facebook - http://www.facebook.com/tommy.doran
Image
Image
Tommy2tone_1999
Teardrop Master
 
Posts: 234
Images: 148
Joined: Tue Oct 21, 2008 10:54 am
Top

Postby bobhenry » Wed Dec 30, 2009 3:21 am

YEP!

Image

Image

Image

Image

out to out 5'7" wide 10' 3" nose to tail

If you are using a H.F. Frame I strongly suggest you use "Nobodys" method of reinforcing the tongue. There are pics in my album of Harvey's repair.
Growing older but not up !
User avatar
bobhenry
Ten Grand Club
Ten Grand Club
 
Posts: 10355
Images: 2614
Joined: Fri Feb 09, 2007 7:49 am
Location: INDIANA, LINDEN
Top

Postby DMcCam » Thu Jan 07, 2010 8:19 pm

What about building a 4 x 10 on a 4 x 8 trailer? Can it be done without a lot of reworking?

Dave
User avatar
DMcCam
Gold Donating Member
 
Posts: 883
Joined: Wed Jan 06, 2010 8:30 pm
Location: Reno, Nevada
Top

Postby Steve_Cox » Tue Jan 19, 2010 7:21 am

DMcCam wrote:What about building a 4 x 10 on a 4 x 8 trailer? Can it be done without a lot of reworking?

Dave



Not too much rework on this one. 2 of the cross members used in the sides to extend them and the axle moved back. Had to drill a few holes. Actual frame length 117", 2X4 on each end during the build brought the length to 10 feet.

Image
Steve
User avatar
Steve_Cox
4000 Club
4000 Club
 
Posts: 4903
Images: 196
Joined: Sun Apr 03, 2005 8:46 am
Location: Albuquerque New Mexico
Top

Postby bobhenry » Tue Jan 19, 2010 7:52 am

Here is a 5x10 on a 5x8 trailer I simply cantalievered the front 2' and extended the tongue.


Image

It would be even easier to cantaliver 1 foot to the front and 1 foot to the rear. This may make a tongue modification unnecessary depending on the trailer
Growing older but not up !
User avatar
bobhenry
Ten Grand Club
Ten Grand Club
 
Posts: 10355
Images: 2614
Joined: Fri Feb 09, 2007 7:49 am
Location: INDIANA, LINDEN
Top

Postby starleen2 » Tue Jan 19, 2010 8:40 am

The Ladybug is 6 X10 on a 4X8 TSC frame with no under framing beyond the trailer itself 8). We just cut off the fenders and built over the wheels
User avatar
starleen2
5th Teardrop Club
 
Posts: 16272
Images: 224
Joined: Sat May 12, 2007 8:26 pm
Location: Pea Ridge ,AR
Top

Postby wannabefree » Tue Jan 19, 2010 9:00 pm

My 5x10, on a 4x8 HF frame:
Image

The front and back actually only overhang the trailer frame by a few inches at the bottom. A foot or so up, though, they overhang a foot. No reason I couldn't have dropped straight down and gotten more length at the bottom; I just liked the curves.

The floor is built on a 4 inch thick torsion box that extends out over the wheels. The 4 inches gives me enough height that I don't have the wheels poking into the sleeping area. The torsion box is 1/4 ply on the bottom, then 1x4, then 3/8 inch ply for the floor. The 3/8 ply is plenty stiff to sleep on.
In anything at all, perfection is finally attained not when there is no longer anything to add, but when there is no longer anything to take away.
-- Antoine de Saint-Exupery
User avatar
wannabefree
The 300 Club
 
Posts: 380
Images: 82
Joined: Fri Jul 11, 2008 11:00 pm
Location: Phoenix
Top

Postby synaps3 » Wed Jan 20, 2010 1:42 pm

Heck, I'm putting a 6.5x12 on a 4x8 frame.

I extended the tongue of the standard HF trailer out an additional 3' to accomplish this. I also flipped the axle to drop the height by about 6". Both mods are necessary for such a large overhang, or the trailer would jacknife at any turn, or might be "tippy." I haven't hit any issues whatsoever so far. I might not even use a substructure below the floor; 5/8" ply seems to be holding the edges quite well at this point.
-- Dave

Build log: here
User avatar
synaps3
The 300 Club
 
Posts: 433
Images: 254
Joined: Sun Nov 08, 2009 1:09 am
Location: Marietta, GA
Top

Postby whitefishpoint » Sat Jan 23, 2010 6:36 pm

Hey! where did you get those moon caps? Are those on the standard HF 12" wheels?

wannabefree wrote:My 5x10, on a 4x8 HF frame:
Image

The front and back actually only overhang the trailer frame by a few inches at the bottom. A foot or so up, though, they overhang a foot. No reason I couldn't have dropped straight down and gotten more length at the bottom; I just liked the curves.

The floor is built on a 4 inch thick torsion box that extends out over the wheels. The 4 inches gives me enough height that I don't have the wheels poking into the sleeping area. The torsion box is 1/4 ply on the bottom, then 1x4, then 3/8 inch ply for the floor. The 3/8 ply is plenty stiff to sleep on.
whitefishpoint
Teardrop Advisor
 
Posts: 91
Images: 0
Joined: Fri Sep 18, 2009 9:26 am
Top

Next

Return to Trailer and Chassis Secrets

Who is online

Users browsing this forum: No registered users and 9 guests