Teardrops n Tiny Travel Trailers

4 Doors assemblies. EDIT 2/13/2010, 2 Door assemblies.

Overall measurements are 27-1/2" wide x 35" tall x 1"deep.
Frame is extruded Aluminum. Doors are made of Fiberglas with aluminum framing.
These would make easy installation to your trailer project. Just add the door latch of your choice.



EDIT:
These are test-fit doors that were installed and removed.
Easy installation.

$60 pair, plus $16 shipping per pair to lower 48 states.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

I using these type doors on my TD build and installed a Push-Button Slam-Latch on them. They are 40" tall and 29" wide.
See my doors below. I will be installing a window on each door.

I would like a pair, if they are still available. Whats your prefered method of payment?

PayPal, Money Order, Personal Check(must clear bank before shipping).

I'm holding two pairs for a member from the UK. I have a couple pairs about the same size.

If he doesn't let me know in a timely manner, I'll sell 'em here.

Do you have any in smaller sizes?

synaps3 wrote:Do you have any in smaller sizes?

Not at the moment.
I do have more coming in. What size are you needing?

Approximately 18"x12"

I'd want 2 or 3...

I'm in Atlanta, so shipping from you should be relatively cheap.

Can you get frames in mill finish versus the white finish? Also how thick is the slot for the insert in the door frame itself? And finally can you make doors to specific dimensions say for a cargo hatch?

I have, Suzy's money, ready to spend if you can provide what I'm looking for.

Cheers,

Gus

synaps3 wrote:Approximately 18"x12"

I'd want 2 or 3...

I'm in Atlanta, so shipping from you should be relatively cheap.

I'll find out if that size is available and let you know.

Thanks,

eamarquardt wrote:Can you get frames in mill finish versus the white finish? Also how thick is the slot for the insert in the door frame itself? And finally can you make doors to specific dimensions say for a cargo hatch?

I have, Suzy's money, ready to spend if you can provide what I'm looking for.

Cheers,

Gus

I have yet to acquire door assemblies in a Mill finish. Although, I believe the while frame can be sanded to a Mill finisn. The door itself is a White Fiberglas and would have to be painted or covered.

Most of these door assemblies are built for 1" or 2" walls.
I'm using 2" on my 1-1'/2" walls.

I can usually get doors in different sizes, but cannot buy made to order as these are surplus and test-fit items.

I have my heart set on mill finish al and need specific sizes. I've had some doors made by Al-Rite but am not happy with the quality and some other issues.

Gonna try Camp Inn as he sez he can make exactly what I want but am open to other suggestions.

Thanks,

Gus

No problem, Gus.

Have a good one.

Etech wrote:

synaps3 wrote:Approximately 18"x12"

I'd want 2 or 3...

I'm in Atlanta, so shipping from you should be relatively cheap.

I'll find out if that size is available and let you know.

Thanks,

Just got word.
Sorry, that specific size is unavailable at the moment.


If I run across anything close to those measurements later on, I'll email or PM you.

I have 2 more for sale , this size.

27.5" wide x 35" tall x 1"deep frame.

$60 pair, plus $16 per pair shipping to lower 48 states.

EDIT, 3/5/10: I have only one pair this size left. I do have another pair that measure 25"x37.5" to fit wall thickness up to 2".

I hope you still have these or get more after I get my bonus in a couple weeks.. I'd have to change my build design, but would be nice!

parnold wrote:I hope you still have these or get more after I get my bonus in a couple weeks.. I'd have to change my build design, but would be nice!

No Problem, Paul. I'm sure I'll have a couple left for you. Let me know.