Matching wheels

Ask questions about Harbor Freight trailers, or questions about building your own...
Post a reply

Matching wheels

Postby mixmaster42 » Sat May 28, 2022 8:57 pm

Has anyone thought of using a car or truck hub assembly to build an axle so that they can use matching wheels for their trailer? :thinking:
mixmaster42
Teardrop Inspector
 
Posts: 3
Joined: Thu Jun 29, 2017 3:15 pm
Location: Niagara Falls, Ont.
Top

Re: Matching wheels

Postby Sparksalot » Sat May 28, 2022 9:14 pm

When I put a new axle in last year I did think about it. I didn’t want to have to get bigger fenders and figure how to remount them.
Holy cow, Rose is a teenager now! Done? Surely you jest. A teardrop is never "done".

The Compass Rose build thread: viewtopic.php?t=23213

Inspiration: http://tnttt.com/Design_Library/Trailer%20for%20Two.htm

It's got a cop motor, a 5.3 LS plant, it's got cop tires, cop suspensions, cop shocks. ~ Elwood Blues
User avatar
Sparksalot
Silver Donating Member
 
Posts: 1624
Images: 682
Joined: Fri Feb 15, 2008 9:36 pm
Location: Texas by God
Top

Re: Matching wheels

Postby rjgimp » Sun May 29, 2022 1:30 am

It works fine as long as that tow vehicle and trailer stay together.
:vroom:
-Rob


I hope to make it to a Procrastinators Anonymous meeting someday...
just as soon as the steering committee gets around to scheduling one!
User avatar
rjgimp
500 Club
 
Posts: 785
Images: 7
Joined: Fri Feb 22, 2019 3:59 am
Location: Saint Paul MN
Top

Re: Matching wheels

Postby Captain Monkeyshines » Sun May 29, 2022 2:59 am

Our teardrop has matching wheels and tires to the truck. It works great as long as you like doing 7 tires when it's time to rotate. Also you can get trailer axles with almost any lug pattern to fit your wheels. Ours is 6 bolt Toyota pattern on our Dexter axle

Image

Sent from my SM-G960U1 using Tapatalk
“When You're Alone”
When you're in the kitchen, you've got to behave
You don't put metal in the microwave
The knobs on the stove are “hands off” no doubt
And when you make toast, don't use a knife to fish it out!
When you're alone, when you're alone
You got to stay safe when you're home all alone.
When you're alone, when you're home all alone
You got to make sure not to die, or choke or burn the house down.
User avatar
Captain Monkeyshines
Teardrop Advisor
 
Posts: 84
Images: 1
Joined: Wed Jan 25, 2012 9:23 pm
Location: A galaxy not too far away
Top

Re: Matching wheels

Postby tony.latham » Sun May 29, 2022 9:15 am

Ours is 6 bolt Toyota pattern on our Dexter axle...


Why is it I don't see the end of the hub sticking out from the wheel?

Image

Tony :thinking:
User avatar
tony.latham
Gold Donating Member
 
Posts: 6900
Images: 17
Joined: Mon Jul 08, 2013 4:03 pm
Location: Middle of Idaho on the edge of nowhere
Top

Re: Matching wheels

Postby Captain Monkeyshines » Sun May 29, 2022 12:08 pm

tony.latham wrote:
Ours is 6 bolt Toyota pattern on our Dexter axle...


Why is it I don't see the end of the hub sticking out from the wheel?

Image

Tony :thinking:
Because that wheel has a 1 inch spacer on it so I can keep my TRD center caps.

Sent from my SM-G960U1 using Tapatalk
“When You're Alone”
When you're in the kitchen, you've got to behave
You don't put metal in the microwave
The knobs on the stove are “hands off” no doubt
And when you make toast, don't use a knife to fish it out!
When you're alone, when you're alone
You got to stay safe when you're home all alone.
When you're alone, when you're home all alone
You got to make sure not to die, or choke or burn the house down.
User avatar
Captain Monkeyshines
Teardrop Advisor
 
Posts: 84
Images: 1
Joined: Wed Jan 25, 2012 9:23 pm
Location: A galaxy not too far away
Top

Re: Matching wheels

Postby mixmaster42 » Mon May 30, 2022 1:34 pm

I should say where I saw the idea was on a Youtube channel "Dirt Lifestyle". The fellow used a Land rover rear axle with the axle ends cut and bolted back up to hold the unit bearing together. This setup gave him the bolt pattern he needed. Using a unit bearing would be slightly harder at the start but easier to fix on a lite trailer. Non drive unit bearings are crimped to hold together.
mixmaster42
Teardrop Inspector
 
Posts: 3
Joined: Thu Jun 29, 2017 3:15 pm
Location: Niagara Falls, Ont.
Top

Re: Matching wheels

Postby schnottus » Sat Jun 11, 2022 12:23 am

I went with wheels that match my 4runner when i built mine this winter, 32in tires on 17in rims.

169474

Dexter has all sorts of options, like the 6 on 5.5 pattern hubs seen above. I did have to weld up custom fenders, but i was planning to anyways.
schnottus
Teardrop Builder
 
Posts: 40
Images: 32
Joined: Sun Oct 17, 2021 12:44 pm
Top
Post a reply

Return to Trailer and Chassis Secrets

Who is online

Users browsing this forum: No registered users and 10 guests

Custom Development by Motivo Solutions | Powered by phpBB® Forum Software © phpBB Group