Page 3 of 9

Re: New to me 7x14 CT conversion

PostPosted: Fri Aug 22, 2014 1:26 pm
by lrrowe
Looks good.

Re: New to me 7x14 CT conversion

PostPosted: Fri Aug 22, 2014 1:27 pm
by Jiffypop207
Thank you.

Re: New to me 7x14 CT conversion

PostPosted: Fri Aug 22, 2014 4:39 pm
by hankaye
Jiffypop207, Howdy;

Looks Wicked bad!
How long till you get the replacement cap?

hank

Re: New to me 7x14 CT conversion

PostPosted: Fri Aug 22, 2014 6:52 pm
by Jiffypop207
hankaye wrote:Jiffypop207, Howdy;

Looks Wicked bad!
How long till you get the replacement cap?

hank


He said they would send it early next week.

Re: New to me 7x14 CT conversion

PostPosted: Sat Aug 23, 2014 2:27 pm
by bc toys
where did you get the awning from Im looking for one for my trailer

Re: New to me 7x14 CT conversion

PostPosted: Sat Aug 23, 2014 4:08 pm
by Jiffypop207
bc toys wrote:where did you get the awning from Im looking for one for my trailer




Scotties awning. They are out of Florida. I ordered completely off the online catalog. Called when I had an issue and they wwere very prompt and helpful. The awning I got is the pioneer lite.

Adam

Re: New to me 7x14 CT conversion

PostPosted: Wed Sep 10, 2014 3:40 pm
by Jiffypop207
Last few weeks have been too hot to work on the trailer. Been in the 60's after work this week so I dug back in. I received the new cap for the damaged awning one the end of last week. I have not swapped it out yet. I pulled the wheels to get new tires. The tires on the trailer when I bought it were all dry rotted bad. They spare was flat. I got 5 new Towmax radial tires sized STR 205/75/R15 mounted and balanced for $380. It was a hell of a deal. I took a couple pictures of the trailer with the wheels off as it looked pretty funny

Image
Image

Took a day to get the tires back so I mounted the storage box on the tongue. I used 2"x2"x1/8" aluminum angle for the mounting tabs. They were fastened to the frame with 2 #14 stainless self tappers each. A 1/2" Stainless bolt will hold the box to each bracket.

Image

I put some Vycor window and door flashing tape over the top of the frame rails to ease rubbing and rust potential

Image

I positioned the tank mount and did the same proceedure

Image

A shot of everything mounted in place

Image

Yesterday I put the wheels back on. I greased all the Dexter EZ Lube hubs first. I got some chrome acorn lugs to keep the stud threads in better condition. They also look pretty sharp

Image
Image

It is going to be time to hop back inside to work again soon so I leveled up the trailer. I had picked up two of the Andersen-3604 Camper Levelers. All I can say is they are worth every penny in my mind. Leveled the trailer alone in about 3 minutes including going to read the 4' level I put on the floor a total of 6 times to read both directions.

The levelers placed to use

Image

And leveled. My driveway has more slope than I thought

Image
Image

I also picked up a cover for the spare to protect it and keep everything going white like it is. Here is the trailer ready for the next steps.

Image
Image

More to come soon....

Adam

Re: New to me 7x14 CT conversion

PostPosted: Wed Sep 10, 2014 5:55 pm
by lrrowe
It looks great sitting in your drive. Much better then an regular ole RV. :thumbsup: But of course, it would look even better out in the wild! :vroom:

Re: New to me 7x14 CT conversion

PostPosted: Wed Sep 10, 2014 6:22 pm
by Gonefishin
This one might be my favorite build on the forum. The exterior, size, and features sure are! Love that window. Tongue box and propane bottles perfect. Spare tire mount: perfect. Quality all around. A/C. :thumbsup: :thumbsup: :thumbsup:

Re: New to me 7x14 CT conversion

PostPosted: Wed Sep 10, 2014 7:17 pm
by brandon32689
Awesome build, where did you get the awning?

Re: New to me 7x14 CT conversion

PostPosted: Wed Sep 10, 2014 8:02 pm
by Jiffypop207
Thanks for the compliments. The awning is from Scotties awning out of FL online. In the wild next year likely.....lots of driveway pictures to come lol!

Adam

Re: New to me 7x14 CT conversion

PostPosted: Wed Sep 10, 2014 8:05 pm
by brandon32689
Jiffypop207 wrote:Thanks for the compliments. The awning is from Scotties awning out of FL online. In the wild next year likely.....lots of driveway pictures to come lol!

Adam


What size is it and what did one that size run

Re: New to me 7x14 CT conversion

PostPosted: Wed Sep 10, 2014 8:23 pm
by Jiffypop207
This is the one I got. 12', white alumagaurd, Pioneer Lite.

http://scottiescatalog.com/Pioneer-Lite ... teva12.htm

Adam

Re: New to me 7x14 CT conversion

PostPosted: Wed Sep 10, 2014 8:42 pm
by brandon32689
Jiffypop207 wrote:This is the one I got. 12', white alumagaurd, Pioneer Lite.

http://scottiescatalog.com/Pioneer-Lite ... teva12.htm

Adam


Thanks for your help!

And I'm going to continue to follow your thread. Looking great so far I need to add a window to my build still

Re: New to me 7x14 CT conversion

PostPosted: Thu Sep 11, 2014 3:22 pm
by chiefb711
Adam,
Have you gotten any more work done on your CTC this week? I'm getting cabin fever in this dang hospital, and I have ordered so much stuff in the meantime. I also thought up a few more ideas for my CTC.

Ryan