"The Walden" multipurpose camper.
Posted: Mon Jun 20, 2005 12:34 pmGonna start cutting wood next week. Comments welcome and greatly anticipated!
Randy
Randy
Looks like a good un to me.
Is that roof going to have gas struts?
Swizz...
Teardrops n Tiny Travel Trailers
or t n ttt for short (tnttt.com)
https://www.tnttt.com/
"The Walden" multipurpose camper.
Page 1 of 1
Posted: Mon Jun 20, 2005 12:34 pmPosted: Mon Jun 20, 2005 12:44 pmPosted: Mon Jun 20, 2005 12:55 pmswizz wrote:Looks like a good un to me.
Is that roof going to have gas struts?
Swizz...
That would be a good idea, but since I am strong enough to lift them with out it probably not.
Randy
Posted: Mon Jun 20, 2005 3:17 pmMy favorite thing about this trailer is the option of being able to cook inside or out.
Nice feature!
Bev
Nice feature!
Bev
Posted: Mon Jun 27, 2005 3:26 amlooks good...alot of good ideas
Posted: Mon Jun 27, 2005 6:19 amPrinted out and archived. Very good starting point for my next. Many good Ideas.
Geron
Geron
Posted: Mon Jun 27, 2005 7:39 amPosted: Mon Jun 27, 2005 4:03 pmAre you sure you don't want to put some kind of a chamfer on the back of that Walden design?
Can you picture your design in 3D?
Mike...
Can you picture your design in 3D?
Mike...
Posted: Mon Jun 27, 2005 8:21 pmRandy,
I modeled up the Walden so you could see what it looks like in 3D.
Mike...
I modeled up the Walden so you could see what it looks like in 3D.
Mike...
Posted: Mon Jun 27, 2005 11:04 pmWow! Thanks for doing that Mike! That is really neat! 
I do my drafting in photoshop cs. Not the preferred program for drawing but I know it very well. Never tried 3D. probably bad idea for photoshop. Photoshop is still lightyears ahead of the pencil we used 20 something years ago in engineering drafting school.
Couple things, The drawers are 12 in high because that is where everything goes. The bulkhead will be thinned out to 4-6 inches wide on the sides with gusseted corners on top. I want to keep 4 ft 1 in open area in the bulkhead so I can get a sheet of plywood in when I need to haul one.
Backdoors will have windows. and maybe a small one in the front because I want to be able to see out of all 4 sides.
The open side walls in the tail area will be good for hanging clothes and other things.
Still thinking about the roof line. Dont know what else we could do with it.
I am going to start laying up the side in the morning.
Thanks!
Randy
I do my drafting in photoshop cs. Not the preferred program for drawing but I know it very well. Never tried 3D. probably bad idea for photoshop. Photoshop is still lightyears ahead of the pencil we used 20 something years ago in engineering drafting school.
Couple things, The drawers are 12 in high because that is where everything goes. The bulkhead will be thinned out to 4-6 inches wide on the sides with gusseted corners on top. I want to keep 4 ft 1 in open area in the bulkhead so I can get a sheet of plywood in when I need to haul one.
Backdoors will have windows. and maybe a small one in the front because I want to be able to see out of all 4 sides.
The open side walls in the tail area will be good for hanging clothes and other things.
Still thinking about the roof line. Dont know what else we could do with it.
I am going to start laying up the side in the morning.
Thanks!
Randy