The Big Pink, Foamie !

[tac422]

Doc,
I saw your discussion about drip edge...
here's what I did on the toyhauler
I added a piece of aluminum flashing over the gap where the walls meet the frame across the front of the trailer, and added a plastic piece of inner corner molding (used for Masonite panels, I thnk) over the edge of the metal on the bottom down the sides.
Sorry about the blurry picture.

You might notice "Big Pink yellow" on the underside of the new floor

[GPW]

NICE !!! I do now see the need for a good drip edge ..... it solves the floor problem nicely ( if the roof don’t leak ..... )

[tac422]

First camping trip of 2016 !
We went to a Tear Jerkers gathering in Va Beach. First time using the new TV, (is the Big Pink really as big as it looks in the picture ?)

We had a great time and met some really nice people !

[GPW]

It’s just Too CUTE !!!!

[rustytoolss]

Just found this build, Very cool . But did I miss pictures of the finished interior ? I sure would like to see how the inside turned out Questions, Which HF trailer did you use (weight cap), what size tires did you end up using ?, What is the size of your sub floor structure (LxW) ? Last one , What is the size of the bed area ? Sorry to ask all of this. But it's a long topic (many, many, many, pages) I'm sure that some of the answers are their

[tac422]

Hi Rusty,
I'm out of town right now. But I looked through the thread and I don't any recent pix of the inside after finishing the AC install.
There are some before the AC was installed , I'll have to get some when I get back.


Let's see if I can answer your questions...
Which HF trailer did you use (weight cap) 1175# H.F. Chassis
what size tires did you end up using ? Stock 12"
What is the size of your sub floor structure (LxW) ? 10' 3" x 5' 7"
Last one , What is the size of the bed area ? Queen

10'3" long
67" wide
70" tall
The door is 27"x 54-1/2"x 47
Inside height is 68"

[GPW]

Looks SUPER !!!

[mikeschn]

Yep you did a really nice job on that!!!

Mike.

[tac422]

Ok, Here's a tour of the interior.
Looking to the left inside the door...
The 2 top switches control the 12VDC LED light and fan.
The bottom ones control the 110 V outside and inside light and fan.

switches1.jpg (212.39 KiB) Viewed 2799 times

inside11.jpg (214.53 KiB) Viewed 2799 times

The right side of the queen size bed

[tac422]

In this picture is the 115V lights, DC fan, refrigerator, AC, small heater, and porta Loo

inside 51.jpg (207.14 KiB) Viewed 2856 times

Here's the AC slid back through the door.

inside 11.jpg (215.88 KiB) Viewed 2856 times

Here's the rear storage under the Bed platform. You can see the door on the right side.

storgage4.jpg (20.43 KiB) Viewed 2856 times

[peeler]

I really like this build! I started out avoiding curves, but at this point now, I'm thinking of building something like this. Ive been reading this thread, and the other related thread as well. Really just a great little camper. And I think I can get my kerfing right on my first build. I've seen a few different jig/setup methods used for it, looks totally do-able. Great camper here.

[GPW]

Peel , you should have no trouble by following procedures others have successfully done , and if you do , remember we’re here to Help ...

[tac422]

Just checkin into the forum...
Still working on lil Pink, and starting plans for The Big Pink Adventure from Virginia to North Dakota.
Tac

[GPW]

Tac, always Great to hear from you !!! Bon Voyage !!!

[Spotman]

Tim, safe travels. Missed your build on Lil Pink! Is it Bike time out there?

Sent from my SM-G920V using Tapatalk