6x12 V-Nose Build

[abqlloyd]

Decided to start a new thread.

Here's my top-level plan:

1. Remove interior siding.
2. Rough electrical
3. Insulation
4. Reinstall interior siding.
5. Interior cabinets and counters.
6. Finish work

Anyone willing to chime in on the order?

[pchast]

Sounds right.... Adding a door or windows?

[abqlloyd]

ImageUploadedByTapatalk1418268972.519132.jpg (86.21 KiB) Viewed 31549 times

Forgot the mandatory picture.

I've been assembling an array of stuff for over a year. Some is from the old camper, some is new.

Think "really cool tent in wheels".

I'll post more pics tomorrow. It's 8:30 and just leaving work.

[lrrowe]

Nice!
I especially like the TV.
I appreciate your posting as I am trying to decide on the window to buy for the door side. Yours is on the smaller size and high. I am wrestling with considering both of those options.
And the night picture looks sharp. I will have to do that also.

[hankaye]

lrrowe, Howdy;

I'd rather have my windows a bit higher, so if anyone is looking in,
they see my smiling face instead of why I'm smiling, ... were it lower.

hank

[lrrowe]

Agreed. But it takes away space for upper cabinet or shelf storage. But i am glad you said that. I have not cut my opening yet for my first of two windows. I will mock up the options (high or mid level) and see what it feels like.

[abqlloyd]

ImageUploadedByTapatalk1418339893.002350.jpg (126.97 KiB) Viewed 31479 times

Some interior pics.

ImageUploadedByTapatalk1418339873.158254.jpg (107.59 KiB) Viewed 31479 times

ImageUploadedByTapatalk1418339853.350280.jpg (104.65 KiB) Viewed 31479 times

This is the new Drimax OSB. They ignored my request for plywood - special orders just upset them.

The panels are attached with screws and the trim is glued and stapled. When I went to pull the trim pieces I realize it's going to crack because the glue holds fast.

At this point I'm considering replacing the trim with 1/2" poplar and then filling the inset with 1/4" oak plywood. I don't have a source locally for the water-resistant OSB.

[abqlloyd]

Some random questions:

They run the luan across the roof down the middle only. I'm thinking of adding two more strips down each side for additional roof rigidity. Any pros or cons?


I have XPS sheets of insulation. Lots of threads and tips and opinions on the best method. I wanted to spray but the supplier doesn't recommend unless I can get the temp up to 50F for 24 hours.

I talked with a guy who said NOT to glue the insulation - just set in place as tight as possible. Fill the gaps with non-expanding foam. Any thoughts? He felt the glue would just cause issues. In fact, he recommended thin furring strips to put a small air space between the skin and the XPS sheets.

[abqlloyd]

We had that window high for that reason - privacy. I have another window to install between the studs vertically but held off because designs are always in flux.

[lrrowe]

How about using silicone caulk or the foam in a can in the gaps between the roof supports and the skin?

[abqlloyd]

I think the idea is to not use glue or adhesive at all. I looked tonight and think I might buy a PVC lattice and use the strips as small spacers.

[abqlloyd]

ImageUploadedByTapatalk1418355136.404824.jpg (99.34 KiB) Viewed 31404 times

Infrared quartz heater. I like the compact size and the zero clearance on the sides. Only three inches clearance on back. I can set in a shelf not take up too much space.

[lrrowe]

I think the idea is to not use glue or adhesive at all. I looked tonight and think I might buy a PVC lattice and use the strips as small spacers.

Why is that? So the roof skin will move with temperature changes?

[abqlloyd]

I'm not sure. I think part is that adhesive traps moisture against the side, not allowing condensation a path. I wish I could spray foam.

[Rainier70]

I did not consider gluing my insulation in for two reasons.

One to allow the skin to flex and move with both temperature and rough roads.

Two is probably the main one ...condensation. In looking at my ct's skin I noticed that it isn't sealed on the bottom and it isn't sealed on the side seams. The side seams (vertical) overlap from front to back, but on the back seam of each panel I could see light through the gaps between the screws. At first I thought I should seal those, but then I considered condensation and I didn't. Those gaps allow any moisture that migrates from the inside to the outside walls a path of escape. I am sure that no matter how I seal the inside that condensation will make its way in there. I wanted to keep that path for moisture out open.